SCANCOM OPC Items
- Michael Standal
- Emma Fullilove (Deactivated)
Standard Items
Protocol Items
The ScanCom protocol implementation supports item names. Items available in the ScanCom device are one of four different types: General, System, FRDM and Hardware.
General Items (All Models)
| Item | Data Type | Description |
|---|---|---|
DemandGCUpload | UI1 | Demand GC Upload. Enter the run number to access after the /. Example: DemandGCUpload/1. |
LastAlarmRecord | Date | Timestamp of the latest Alarm record collected from the device. |
LastChangeLogRecord | Date | Timestamp of the latest Change Log record collected from the device. |
LastDailyRecord/n | Date | Timestamp of the latest Daily Upload record collected from Meter n. |
LastDemandGCRecord | Date | Timestamp of the latest Demand GC record collected from the device. |
LastDLogRecord/n | Date | Timestamp of the latest DLog record collected from DLog n. |
LastEventRecord | Date | Timestamp of the latest Event record collected from the device. |
LastHourlyRecord/n | Date | Timestamp of the latest Hourly Upload record collected from Meter n. |
LastTimeSync | Date | Timestamp of the last time sync. |
LastTimeSyncResult | I4 | Result code for the last time sync: 0 for no error or alarm. Error and alarm result code values are set in the Time Sync object. |
MoveHourly | UI4 | Move Hourly Upload position pointer. |
TimeSync | I2 | Synchronize Time |
System Items (All Models)
| Item | Access | Data Type | Scancom ID and Description |
|---|---|---|---|
Bat_Voltage | Read Only | R4 | (0006) Input battery voltage. |
Board_ID | Read Only | BSTR | (0004) Scanner board ID number. |
Cert_TimeDate | Read Only | DATE | (000F) Certification date time stamp. |
CFG_lock_status | Read Only | UI1 | (001D) CFG lockout status |
Charge_Voltage | Read Only | R4 | (0008) Input battery charge voltage |
FR_Check_alarm_cfg | Read/Write | UI1 | (0018) Flow run check alarm configuration. Bit 0 = Log in event log. Bit 1 = Show in network alarms & alarm page. |
Gas_Day | Read/Write | I2 | (0007) Indicates the gas day hour based on contract hour. 0 - 23 |
HW_Range_alarm_cfg | Read/Write | UI1 | (0017) Hardware range alarm configuration. Bit 0 = Log in event log. Bit 1 = Show in network alarms & alarm page. |
Low_Bat_Dband | Read/Write | R8 | (0012) Low battery alarm dead band. |
Low_Bat_Limit | Read/Write | R8 | (0011) Low battery alarm set point. |
Low_Battery_AlStat | Read Only | UI2 | (0013) Low battery alarm status |
Meas_Change_Cnt | Read Only | UI2 | (0022) Measurement change counter. |
Model_No | Read Only | UI2 | (0001) The scanner model number. |
Node_name | Read/Write | BSTR | (0005) Unit node name. |
Num_Runs | Read Only | UI1 | (0021) Number of flow runs in use in the device. |
NVRAM_Voltage | Read Only | R4 | (000E) NVRAM backup battery voltage. |
Pwr_Save_Mode | Read/Write | UI1 | (0060) Power save mode. 0 = Full power. 1 = Conserve power. |
Serial_No | Read Only | BSTR | (0003) Unit serial number. |
Soft_Ver | Read Only | BSTR | (0002) Software version. |
Stn_No | Read Only | UI2 | (0020) Station number. |
Superboot_flag | Read Only | UI1 | (0000) Super boot flag 0/1. 0 = Normal. 1 = Super Boot Mode |
System_AlStat | Read Only | UI2 | (0019) System alarm page status 0/1 |
TimeDate | Read Only | DATE | (0010) Device time. |
Uchg_lock_bytes | Read Only | UI2 | (001E) Change lock bytes. |
Unit_Temp | Read Only | R4 | (0009) Ambient unit temperature. |
Unit_Vref | Read/Write | R8 | (000A) ATOD System Voltage Reference |
UserChg_No | Read Only | UI2 | (0023) Last User Change number |
UserChg_Size | Read Only | UI2 | (002D) User change log size in bytes. |
Hardware Items General
Hardware items use the .XX/X modifiers to specify the resource parameter and slot number to access. Resource parameters should be converted from HEX to a decimal number.
Example: HardwareAnalogInput01.16/1 would access HEX parameter 10 on slot 1 for item HardwareAnalogInput01.
Hardware Items (1130 Model)
| Item | Data Type | Access | Scancom ID (HEX) | Description |
|---|---|---|---|---|
AnalogIn1_0x0505 | R8 | Read/Write | 0x0505 | Analog Input #1 (A05) |
AnalogIn2_0x0506 | R8 | Read/Write | 0x0506 | Analog Input #2 (A06) |
AnalogIn3_0x0507 | R8 | Read/Write | 0x0507 | Analog Input #3 (A07) |
AnalogIn4_0x0508 | R8 | Read/Write | 0x0508 | Analog Input #4 (A08) |
AnalogIn5_0x0509 | R8 | Read/Write | 0x0509 | Analog Input #5 (A09) |
AnalogIn6_0x050A | R8 | Read/Write | 0x050A | Analog Input #6 (A10) |
Status1_0x010D | R8 | Read/Write | 0x010D | Status Input #1 (A13) |
Status2_0x010E | R8 | Read/Write | 0x010E | Status Input #2 (A14) |
| StatusInDI01_0x0101 | R8 | Read/Write | 0x0101 | Status Input (X01) |
StatusInCD01x2_0x0102 | R8 | Read/Write | 0x0102 | Status Input (X02) |
StatusInCD01x3_0x0103 | R8 | Read/Write | 0x0103 | Status Input (X03) |
StatusInCD01x4_0x0104 | R8 | Read/Write | 0x0104 | Status Input (X04) |
StatusInCD01x5_0x0105 | R8 | Read/Write | 0x0105 | Status Input (X05) |
| PulseInputX01_0x0301 | R8 | Read/Write | 0x0301 | Pulse Input (X01) |
| PulseInputX02_0x0302 | R8 | Read/Write | 0x0302 | Pulse Input (X02) |
| PulseIn1_0x0304 | R8 | Read/Write | 0x0304 | Pulse Input #1 (A04) |
| PulseIn2_0x030B | R8 | Read/Write | 0x030B | Pulse Input #2 (A11) |
Hardware Items (1131 Model)
| Item | Data Type | Access | Scancom ID (HEX) | Description |
|---|---|---|---|---|
AnalogIn1_0x050F | R8 | Read/Write | 0x050F | Analog Input #1 (A15) |
AnalogIn2_0x0511 | R8 | Read/Write | 0x0511 | Analog Input #2 (A17) |
AnalogIn3_0x0513 | R8 | Read/Write | 0x0513 | Analog Input #3 (A19) |
AnalogIn4_0x0515 | R8 | Read/Write | 0x0515 | Analog Input #4 (A21) |
AnalogIn5_0x0517 | R8 | Read/Write | 0x0517 | Analog Input #5 (A23) |
AnalogIn6_0x0519 | R8 | Read/Write | 0x0519 | Analog Input #6 (A25) |
| AnalogIn7_0x0510 | R8 | Read/Write | 0x0510 | Analog Input #7 (A16) |
| AnalogIn8_0x0512 | R8 | Read/Write | 0x0512 | Analog Input #8 (A18) |
| AnalogIn9_0x0514 | R8 | Read/Write | 0x0514 | Analog Input #9 (A20) |
| AnalogIn10_0x0516 | R8 | Read/Write | 0x0516 | Analog Input #10 (A22) |
| AnalogIn11_0x0518 | R8 | Read/Write | 0x0518 | Analog Input #11 (A24) |
| AnalogIn12_0x051A | R8 | Read/Write | 0x051A | Analog Input #12 (A26) |
Status1_0x0107 | R8 | Read/Write | 0x0107 | Status Input (A07) |
Status2_0x0108 | R8 | Read/Write | 0x0108 | Status Input (A08) |
| Status3_0x0109 | R8 | Read/Write | 0x0109 | Status Input (A09) |
| Status4_0x010A | R8 | Read/Write | 0x010A | Status Input (A10) |
| Status5_0x010B | R8 | Read/Write | 0x010B | Status Input (A11) |
| Status6_0x010C | R8 | Read/Write | 0x010C | Status Input (A12) |
| StatusInDI01_0x0101 | R8 | Read/Write | 0x0101 | Status Input (X01) |
StatusInCD01x2_0x0102 | R8 | Read/Write | 0x0102 | Status Input (X02) |
StatusInCD01x3_0x0103 | R8 | Read/Write | 0x0103 | Status Input (X03) |
StatusInCD01x4_0x0104 | R8 | Read/Write | 0x0104 | Status Input (X04) |
StatusInCD01x5_0x0105 | R8 | Read/Write | 0x0105 | Status Input (X05) |
| PulseInputX01_0x0301 | R8 | Read/Write | 0x0301 | Pulse Input (X01) |
| PulseInputX02_0x0302 | R8 | Read/Write | 0x0302 | Pulse Input (X02) |
| PulseIn1_0x0305 | R8 | Read/Write | 0x0305 | Pulse Input #1 (A05) |
| PulseIn1_0x0306 | R8 | Read/Write | 0x0306 | Pulse Input #2 (A06) |
Hardware Items (1140 Model)
| Item | Data Type | Access | Resource ID (HEX) | Description |
|---|---|---|---|---|
AnalogIn1_0x0509 | R8 | Read/Write | 0509 | Analog Input #1 (A09) |
| AnalogIn2_0x050A | R8 | Read/Write | 050A | Analog Input #2 (A10) |
| Status1_0x0103 | R8 | Read/Write | 0103 | Status Input #1 (A03) |
| Status2_0x0104 | R8 | Read/Write | 0104 | Status Input #2 (A04) |
| Status3_0x0105 | R8 | Read/Write | 0105 | Status Input #3 (A05) |
| Status4_0x0106 | R8 | Read/Write | 0106 | Status Input #4 (A06) |
| PulseIn1_0x0307 | R8 | Read/Write | 0307 | Pulse Input #1 (A07) |
FRDM (Flow Run Data Manager - All Models) Items
FRDM items need a /X modifier to indicate the flow run number to access.
Example: 0101/1 would access item 0101 on flow run number 1.
| Item (HEX) | Access | Data Type | Description |
|---|---|---|---|
0E03 | Read/Write | R8 | Yesterdays Total Mass |
0E01 | Read Only | R8 | Mass Flow Rate |
0E02 | Read/Write | R8 | Todays Total Mass |
0E04 | Read/Write | R8 | Total Mass |
0E05 | Read/Write | R8 | This Months Total Mass |
0E06 | Read/Write | R8 | Previous Months Total Mass |
| 0101 | Read Only | R8 | Gauge Pressure |
| 0102 | Read Only | R8 | Live Temperature |
| 0103 | Read/Write | R8 | Absolute Pressure |
| 0104 | Read/Write | R8 | Local Atmospheric Pressure |
0107 | Read Only | R8 | Temperature for Zf |
0108 | Read Only | R8 | Absolute Pressure for Zf |
0109 | Read Only | R8 | Last read Temperature |
| 0301 | Read Only | R8 | Todays Total Volume |
0302 | Read/Write | R8 | Yesterdays Total Volume |
| 0303 | Read Only | R8 | Volume Flow Rate |
| 0304 | Read Only | R8 | Input Live 1 |
| 0305 | Read Only | R8 | Input Live 2 |
| 0306 | Read/Write | R8 | Total Volume |
0308 | Read/Write | R8 | This Months Total Volume |
0309 | Read/Write | R8 | Previous Months Total Volume |
| 0401 | Read/Write | R8 | Expansibility Factor |
| 0402 | Read/Write | R8 | Current Differential Pressure |
| 0403 | Read/Write | R8 | Uncorrected Pipe Inside Diameter |
| 0404 | Read/Write | R8 | Uncorrected throat diameter |
| 0405 | Read/Write | R8 | Velocity of Approach factor |
| 0406 | Read/Write | R8 | Absolute viscosity |
0407 | Read/Write | R8 | Isentropic Exponent |
0408 | Read Only | R8 | Diameter ratio |
0409 | Read Only | R8 | Pipe Inside Diameter |
0410 | Read Only | R8 | Reynolds Number (D) |
0411 | Read Only | R8 | Interpolated Meter Factor |
0412 | Read/Write | R8 | Meter factor 1 |
0413 | Read/Write | R8 | Meter factor 2 |
0414 | Read/Write | R8 | Meter factor 3 |
0415 | Read/Write | R8 | Meter factor 4 |
0416 | Read/Write | R8 | Meter factor 5 |
0417 | Read/Write | R8 | Meter factor 6 |
0418 | Read/Write | R8 | Meter factor 7 |
0419 | Read/Write | R8 | Meter factor 8 |
0420 | Read/Write | R8 | Meter factor Reynolds Number 6 |
0421 | Read/Write | R8 | Meter factor Reynolds Number 7 |
0422 | Read/Write | R8 | Meter factor Reynolds Number 8 |
0423 | Read/Write | R8 | Meter factor Reynolds Number 9 |
0501 | Read/Write | R8 | Contract base pressure |
0502 | Read/Write | R8 | Gas base temperature |
0601 | Read Only | R8 | Fluid Density |
0701 | Read Only | R8 | Gas relative density |
0801 | Read/Write | R8 | Gas Flowing Compressibility |
0802 | Read Only | R8 | Molar density, flowing conditions |
0902 | Read Only | R8 | Molar Mass |
1001 | Read/Write | R8 | Gas base heating value |
1101 | Read Only | R8 | Gas energy flow rate |
1102 | Read/Write | R8 | Gas total energy today |
1103 | Read/Write | R8 | Yesterdays Total Energy |
1104 | Read/Write | R8 | Total Energy |
1105 | Read/Write | R8 | This Months Total Energy |
1106 | Read/Write | R8 | Previous Months Total Energy |
1201 | Read/Write | R8 | Heating value, mass basis |
1701 | Read/Write | R8 | Pseudo critical pressure |
1702 | Read/Write | R8 | Pseudo critical temperature |
1801 | Read/Write | R8 | Mole fraction carbon dioxide (CO2). |
1802 | Read/Write | R8 | Mole fraction Nitrogen (O2) |
1803 | Read/Write | R8 | Mole fraction Methane (C1). |
1804 | Read/Write | R8 | Mole fraction ethane (C2). |
1805 | Read/Write | R8 | Mole fraction Propane (C3). |
1806 | Read/Write | R8 | Mole fraction Normal Butane (C4) |
1807 | Read/Write | R8 | Mole fraction Iso-Butane (IC4) |
1808 | Read/Write | R8 | Mole fraction Normal Pentane (C5) |
1809 | Read/Write | R8 | Mole fraction Iso-Pentane (IC5) |
1810 | Read/Write | R8 | Mole fraction carbon monoxide (CO). |
1811 | Read/Write | R8 | Mole fraction hydrogen (H2). |
1812 | Read/Write | R8 | Mole fraction Hydrogen Sulfide (H2S) |
1813 | Read/Write | R8 | Mole fraction water (H2O) |
1814 | Read/Write | R8 | Mole fraction helium (He) |
1815 | Read/Write | R8 | Mole fraction Argon (AR). |
1816 | Read Only | R8 | Gas mole fraction sum |
1901 | Read/Write | R8 | Matrix pressure point 1 |
1902 | Read/Write | R8 | Matrix pressure point 2 |
1903 | Read/Write | R8 | Matrix pressure point 3 |
1904 | Read/Write | R8 | Matrix temperature point 1 |
1905 | Read/Write | R8 | Matrix temperature point 2 |
1906 | Read/Write | R8 | Matrix temperature point 3 |
1907 | Read/Write | R8 | Z factor @ Pressure1 / Temperature 1 |
1908 | Read/Write | R8 | Z factor @ Pressure1 / Temperature 2 |
1909 | Read/Write | R8 | Z factor @ Pressure1 / Temperature 3 |
2E01 | Read/Write | R8 | Mole Fraction Ethene |
| 2E02 | Read/Write | R8 | Mole Fraction Propene |
2E03 | Read/Write | R8 | Mole Fraction Butene |
| 2E04 | Read/Write | R8 | Mole Fraction Pentene-1 |
2301 | Read Only | R8 | Heating value volume basis ref. conditions |
2401 | Read Only | R8 | Single Live Differential Pressure |
2501 | Read Only | R8 | Low Stacked Differential Pressure |
2502 | Read Only | R8 | High Stacked Differential Pressure |
2601 | Read/Write | R8 | Stacked DP low to high switchpoint |
2602 | Read/Write | R8 | Stacked DP high to low switch point |
2701 | Read Only | R8 | Mid Stacked Differential Pressure |
2702 | Read/Write | R8 | Stacked DP low to mid switchpoint |
2703 | Read/Write | R8 | Stacked DP mid to low switchpoint |
2704 | Read/Write | R8 | Stacked DP mid to high switchpoint |
2705 | Read/Write | R8 | Stacked DP high to mid switchpoint |
2801 | Read Only | R8 | Primary Live Differential Pressure |
2802 | Read Only | R8 | Secondary Live Differential Pressure |
3101 | Read Only | R8 | Ultrasonic Meter factor (interpolated) |
3102 | Read/Write | R8 | Ultrasonic Meter factor 1 |
3103 | Read/Write | R8 | Ultrasonic Meter factor 2 |
3104 | Read/Write | R8 | Ultrasonic Meter factor 3 |
3105 | Read/Write | R8 | Ultrasonic Meter factor 4 |
3106 | Read/Write | R8 | Ultrasonic Meter factor 5 |
3107 | Read/Write | R8 | Ultrasonic Meter factor 6 |
3108 | Read/Write | R8 | Ultrasonic Meter factor 7 |
3109 | Read/Write | R8 | Ultrasonic Meter factor 8 |
3110 | Read/Write | R8 | Ultrasonic Meter factor Of 6 |
3111 | Read/Write | R8 | Ultrasonic Meter factor Of 7 |
3112 | Read/Write | R8 | Ultrasonic Meter factor Of 8 |
3113 | Read/Write | R8 | Ultrasonic Meter factor Of 9 |
4201 | Read/Write | R8 | Gas Reference Compressibility |
4202 | Read Only | R8 | Molar density, reference conditions |
4301 | Read Only | R8 | Fluid Density Ref |
4501 | Read Only | R8 | Peak Pressure (hourly) |
4502 | Read Only | R8 | Peak Pressure (daily) |
4503 | Read Only | R8 | Peak Volume Flow Rate (hourly) |
4504 | Read Only | R8 | Peak Volume Flow Rate (daily) |
4701 | Read/Write | R8 | Annubar Coefficient 1 |
4702 | Read/Write | R8 | Annubar Coefficient 2 |
4703 | Read Only | R8 | Annubar Flow Coefficient |
010A | Read Only | R8 | Last read Pressure |
010B | Read Only | R8 | Gas flowing temperature |
010C | Read Only | R8 | Last read Differential Pressure |
020B | Read Only | R8 | Fluid Density Base |
040A | Read Only | R8 | Throat Diameter |
040B | Read/Write | R8 | Pipe thermal expansion coefficient |
040C | Read/Write | R8 | Pipe Measurement Temperature |
040D | Read/Write | R8 | Throat thermal expansion coefficient |
040E | Read/Write | R8 | Throat measurement temperature |
040F | Read/Write | R8 | Discharge Coefficient |
041A | Read/Write | R8 | Meter factor 9 |
041B | Read/Write | R8 | Meter factor Reynolds Number 1 |
041C | Read/Write | R8 | Meter factor Reynolds Number 2 |
041D | Read/Write | R8 | Meter factor Reynolds Number 3 |
041E | Read/Write | R8 | Meter factor Reynolds Number 4 |
041F | Read/Write | R8 | Meter factor Reynolds Number 5 |
0B01 | Read Only | R8 | Uncorrected Pulse Rate |
0B02 | Read Only | R8 | Uncorrected Pulse Total |
0B03 | Read Only | R8 | Input frequency |
0B04 | Read Only | R8 | Average Uncorrected Pulse Rate |
0C01 | Read/Write | R8 | Gas Base Compressibility |
0C02 | Read Only | R8 | Molar density, base conditions |
| 180A | Read/Write | R8 | Mole Fraction Normal Hexane (C6) |
180B | Read/Write | R8 | Mole fraction Normal Heptane (C7) |
180C | Read/Write | R8 | Mole fraction Normal Octane (C8) |
180D | Read/Write | R8 | Mole fraction Normal Nonane (C9) |
180E | Read/Write | R8 | Mole fraction Normal Decane (C10) |
180F | Read/Write | R8 | Mole fraction Oxygen (O2) |
190A | Read/Write | R8 | Z factor @ Pressure2 / Temperature 1 |
190B | Read/Write | R8 | Z factor @ Pressure2 / Temperature 2 |
190C | Read/Write | R8 | Z factor @ Pressure2 / Temperature 3 |
190D | Read/Write | R8 | Z factor @ Pressure3 / Temperature 1 |
190E | Read/Write | R8 | Z factor @ Pressure3 / Temperature 2 |
190F | Read/Write | R8 | Z factor @ Pressure3 / Temperature 3 |
1A01 | Read/Write | R8 | Matrix pressure point 4 |
1A02 | Read/Write | R8 | Matrix pressure point 5 |
1A03 | Read/Write | R8 | Matrix temperature point 4 |
1A04 | Read/Write | R8 | Matrix temperature point 5 |
1A05 | Read/Write | R8 | Z factor @ Pressure1 / Temperature 4 |
1A06 | Read/Write | R8 | Z factor @ Pressure1 / Temperature 5 |
1A07 | Read/Write | R8 | Z factor @ Pressure2 / Temperature 4 |
1A08 | Read/Write | R8 | Z factor @ Pressure2 / Temperature 5 |
1A09 | Read/Write | R8 | Z factor @ Pressure3 / Temperature 4 |
1A0A | Read/Write | R8 | Z factor @ Pressure3 / Temperature 5 |
1A0B | Read/Write | R8 | Z factor @ Pressure4 / Temperature 1 |
1A0C | Read/Write | R8 | Z factor @ Pressure4 / Temperature 2 |
1A0D | Read/Write | R8 | Z factor @ Pressure4 / Temperature 3 |
1A0E | Read/Write | R8 | Z factor @ Pressure4 / Temperature 4 |
1A0F | Read/Write | R8 | Z factor @ Pressure4 / Temperature 5 |
1A10 | Read/Write | R8 | Z factor @ Pressure5 / Temperature 1 |
1A11 | Read/Write | R8 | Z factor @ Pressure5 / Temperature 2 |
1A12 | Read/Write | R8 | Z factor @ Pressure5 / Temperature 3 |
1A13 | Read/Write | R8 | Z factor @ Pressure5 / Temperature 4 |
1A14 | Read/Write | R8 | Z factor @ Pressure5 / Temperature 5 |
310A | Read/Write | R8 | Ultrasonic Meter factor 9 |
310B | Read/Write | R8 | Ultrasonic Meter factor Of 1 |
310C | Read/Write | R8 | Ultrasonic Meter factor Of 2 |
310D | Read/Write | R8 | Ultrasonic Meter factor Of 3 |
310E | Read/Write | R8 | Ultrasonic Meter factor Of 4 |
310F | Read/Write | R8 | Ultrasonic Meter factor Of 5 |
FF00 | Read/Write | UI1 | R/W Access Flags |
FF01 | Read/Write | UI1 | Flowrun status (O=stopped, 1 setup, 2=running, 3=standby ) |
FF02 | Read/Write | UI2 | Calculation delay |
FF03 | Read/Write | UI1 | Z factor counter |
FF04 | Read Only | UI1 | Averaging delay (old) |
FF05 | Read/Write | UI1 | Estimation off/on |
FF06 | Read/Write | UI1 | Estimation basis |
FF07 | Read/Write | R4 | Flow check limit |
FF08 | Read/Write | R4 | DP check limit |
FF09 | Read Only | Date | Gas composition last change date |
FF0A | Read Only | VT_DATE | Plate change date |
FF0B | Read/Write | STRING | Gas Component Ref String |
FF0C | Read/Write | UI1 | Gas Component Origin |
FF0D | Read/Write | UI4 | Gas Component Ref No |
FF0E | Read Only | UI1 | Flowing direction (0=Forward, 1=Unspecified, 2=Reverse, 3=Status In) |
FF0F | Read/Write | UI4 | Averaging delay |
FF10 | Read Only | UI1 | The volume, mass energy calculation method. 1= Volume Only, 2 = Mass Only, 3 = Volume & Mass, 5 = Volume & Energy, 6 = Mass & Energy, 7 = Volume, Mass, & Energy |
FF12 | Read Only | UI1 | Primary measurement device used. 0 =Differential producers, 1 = Linear volume meter, 2= linear mass meter |
FF13 | Read Only | UI1 | The device type. Orifice Run(0 = Orifice meter, 1= Pitot Tube, 2 = Inverted Venturi, 9 = Entered Cd&Y) Turbine Run(0 = Standard, 1 = Level B, 2 = Ultrasonic) |
FF14 | Read Only | UI1 | The tap type. 0 = Flange Taps |
FF15 | Read Only | UI1 | The tap location. 0 = Upstream, 1 = Downstream |
| FF16 | Read Only | UI1 | DP Mode. 0=Single, 1= Dual Stacked, 2= Triple Stacked, 3= Dual Checking |
FF17 | Read Only | UI1 | Gas data type |
FF18 | Read Only | UI1 | Z method in use. 0 = Matrix, 5 = Standing Katz, 6 = RedlichKwong, 14 = AGA8 (1992), 15 = GHC, 16 = SGERG GHN, 18 = AGA8 (1992) |
FF19 | Read Only | UI1 | Z matrix size (D=single , 1 =3x3 Matrix, 2=5x5 Matrix) |
| FF1A | Read Only | UI1 | Energy Calibration Basis |
FF1B | Read Only | UI1 | Gravity Mode in use. 0 = Calculated, 1 = Entered, 2 = Live, 4 = Calculated and logged, 5 = Entered and logged |
FF1C | Read Only | UI1 | Gas heating value mode |
| FF1D | Read Only | UI1 | History Log Size. 0= 8 Days, 1= 35 Days, 2= 60 Days, 3= 1 Day, 4= 15 Days |
FF1E | Read Only | R8 | System input voltage |
FF1F | Read/Write | BSTR | Flowrun name |
FF20 | Read Only | R4 | Qb estimated flowrate |
FF21 | Read Only | R4 | Qm estimated flowrate |
FF22 | Read Only | R4 | Qe estimated flowrate |
FF23 | Read/Write | UI2 | Current measurement status 1 |
FF24 | Read Only | UI1 | Gas component logging on or off. 0 = Off, 1 = Hourly log, 2 = Daily log, 3 = Hourly and Daily logs |
FF27 | Read Only | UI2 | History logs interval in minutes. |
FF28 | Read/Write | UI1 | Averaging style (O=Flowtime, 1=Fulltime, 2="0" Flowtime) |
FF29 | Read Only | UI1 | Gas component mode (1=Entered) |
FF2A | Read/Write | UI4 | Direction Status in |
FF2B | Read/Write | BSTR | Plate serial number |
FF2C | Read Only | R8 | Daily Flowtime |
FF2E | Read Only | R8 | Yesterdays Flowtime |
FF2F | Read Only | R8 | Prev. Hours Flowtime |
FF34 | Read/Write | UI1 | Estimate during plate changes |
FF35 | Read/Write | UI1 | Partial records enabled |
FF36 | Read Only | R8 | Monthly Flowtime |
FF37 | Read Only | R8 | Prev. Months Flowtime |
FF39 | Read Only | UI1 | Flow run Type |
FF3A | Read Only | UI1 | The hourly history log size. 0 = No records.. |
FF3B | Read Only | UI1 | Daily History Size |
FF3D | Read Only | UI1 | Qb/Press peak looing (0=Off, 1=Press, 2=0b, 3=0b&Press) |
FF42 | Read Only | UI1 | Density source |
FF47 | Read/Write | UI2 | Current measurement status 2 |
FF48 | Read/Write | UI2 | Current measurement status 3 |
FF49 | Read/Write | UI2 | Current measurement status 4 |
FF4A | Read/Write | UI2 | Current measurement status 5 |
FF4B | Read/Write | UI2 | Current measurement status 6 |
FF4C | Read/Write | UI2 | Current measurement status 7 |
FF4D | Read/Write | UI2 | Current measurement status 8 |
FF4E | Read Only | UI1 | Reference conditions. 0 = User Entered, 1 = United States, 2 = France and Japan, 3 = Canada, United Kingdom, Australia, 4 = Europe |
FF4F | Read/Write | BSTR | Unit Cfg. string |
FF50 | Read Only | UI1 | Last Hour Meas. Status |
FF51 | Read Only | R8 | Last Hour Volume |
FF52 | Read Only | R8 | Last Hour Mass |
FF53 | Read Only | R8 | Last Hour Energy |
FF54 | Read Only | R8 | Last Hour Uncorr. Volume/Freq |
FF55 | Read Only | R8 | Last Hour DiffP |
FF56 | Read Only | R8 | Last Hour Fextn |
FF57 | Read Only | R8 | Last Hour PI |
FF58 | Read Only | R8 | Last Hour Temp |
FF59 | Read Only | R8 | Last Hour Gr/RHOI |
FF5A | Read Only | R8 | Last Hour Hvb |
FF5B | Read Only | R8 | Last Hour Peak Pressure |
FF5C | Read Only | R8 | Last Hour Peak Volume Rate |
FF60 | Read Only | UI1 | Yesterday's Meas. Status |
FF61 | Read Only | R8 | Yesterday's Volume |
FF62 | Read Only | R8 | Yesterday's Mass |
FF63 | Read Only | R8 | Yesterday's Energy |
FF64 | Read Only | R8 | Yesterday's Uncorr. Volume/Freq |
FF65 | Read Only | R8 | Yesterday's DiffP |
FF66 | Read Only | R8 | Yesterday's Fextn |
FF67 | Read Only | R8 | Yesterday's PI |
FF68 | Read Only | R8 | Yesterday's Temp |
FF69 | Read Only | R8 | Yesterday's Gr/RHOI |
FF6A | Read Only | R8 | Yesterday's Hvb |
FF6B | Read Only | R8 | Yesterday's Peak Pressure |
FF6C | Read Only | R8 | Yesterday's Peak Volume Rate |
FF80 | Read Only | R8 | Hourly Flowtime |
FF8D | Read Only | UI4 | Calculation sync counter |
FF8E | Read/Write | UI1 | Run_Status R/W Flags |
FF8F | Read/Write | UI1 | GC Comp Ref R/W Access Flags |
FF90 | Read Only | R8 | Last Hour Methane |
FF91 | Read Only | R8 | Last Hour Ethane |
FF92 | Read Only | R8 | Last Hour Propane |
FF93 | Read Only | R8 | Last Hour Normal Butane |
FF94 | Read Only | R8 | Last Hour lso Butane |
FF95 | Read Only | R8 | Last Hour Normal Pentane |
FF96 | Read Only | R8 | Last Hour lso Pentane |
FF97 | Read Only | R8 | Last Hour Normal Hexane |
FF98 | Read Only | R8 | Last Hour Normal Heptane |
FF99 | Read Only | R8 | Last Hour Normal Octane |
FF9A | Read Only | R8 | Last Hour Normal Nonane |
FF9B | Read Only | R8 | Last Hour Normal Decane |
FF9C | Read Only | R8 | Last Hour Carbon Dioxide |
FF9D | Read Only | R8 | Last Hour Nitrogen |
FF9E | Read Only | R8 | Last Hour Oxygen |
FF9F | Read Only | R8 | Last Hour Carbon Monoxide |
FFA0 | Read Only | R8 | Last Hour Hydrogen |
FFA1 | Read Only | R8 | Last Hour Hydrogen Sulfide |
FFA2 | Read Only | R8 | Last Hour Water Vapour |
FFA3 | Read Only | R8 | Last Hour Helium |
FFA4 | Read Only | R8 | Last Hour Argon |
FFA5 | Read Only | R8 | Last Hour Ethene |
FFA6 | Read Only | R8 | Last Hour Propene |
FFA7 | Read Only | R8 | Last Hour Butene |
FFA8 | Read Only | R8 | Last Hour Pentene |
FFB0 | Read Only | R8 | Yesterday's Methane |
FFB1 | Read Only | R8 | Yesterday's Ethane |
FFB2 | Read Only | R8 | Yesterday's Propane |
FFB3 | Read Only | R8 | Yesterday's Normal Butane |
FFB4 | Read Only | R8 | Yesterday's lso Butane |
FFB5 | Read Only | R8 | Yesterday's Normal Pentane |
FFB6 | Read Only | R8 | Yesterday's lso Pentane |
FFB7 | Read Only | R8 | Yesterday's Normal Hexane |
FFB8 | Read Only | R8 | Yesterday's Normal Heptane |
FFB9 | Read Only | R8 | Yesterday's Normal Octane |
FFBA | Read Only | R8 | Yesterday's Normal Nonane |
FFBB | Read Only | R8 | Yesterday's Normal Decane |
FFBC | Read Only | R8 | Yesterday's Carbon Dioxide |
FFBD | Read Only | R8 | Yesterday's Nitrogen |
FFBE | Read Only | R8 | Yesterday's Oxygen |
FFBF | Read Only | R8 | Yesterday's Carbon Monoxide |
FFC0 | Read Only | R8 | Yesterday's Hydrogen |
FFC1 | Read Only | R8 | Yesterday's Hydrogen Sulfide |
FFC2 | Read Only | R8 | Yesterday's Water Vapor |
FFC3 | Read Only | R8 | Yesterday's Helium |
FFC4 | Read Only | R8 | Yesterday's Argon |
FFC5 | Read Only | R8 | Yesterday's Ethene |
FFC6 | Read Only | R8 | Yesterday's Propene |
FFC7 | Read Only | R8 | Yesterday's Butene |
FFC8 | Read Only | R8 | Yesterday's Pentene-1 |
Accessory Items (All Models)
| Item | Access | Data Type | Description |
|---|---|---|---|
| SCANPLC_F1 | Read/Write | R8 | 0x01000460 |
| SCANPLC_F2 | Read/Write | R8 | 0x01010460 |
| SCANPLC_F3 | Read/Write | R8 | 0x01020460 |
| SCANPLC_F4 | Read/Write | R8 | 0x01030460 |
| SCANPLC_F5 | Read/Write | R8 | 0x01040460 |
| SCANPLC_F6 | Read/Write | R8 | 0x01050460 |
| SCANPLC_F7 | Read/Write | R8 | 0x01060460 |
| SCANPLC_F8 | Read/Write | R8 | 0x01070460 |
| SCANPLC_F9 | Read/Write | R8 | 0x01080460 |
| SCANPLC_F10 | Read/Write | R8 | 0x01090460 |
| SCANPLC_F11 | Read/Write | R8 | 0x010A0460 |
| SCANPLC_F12 | Read/Write | R8 | 0x010B0460 |
| SCANPLC_F13 | Read/Write | R8 | 0x010C0460 |
| SCANPLC_F14 | Read/Write | R8 | 0x010D0460 |
| SCANPLC_F15 | Read/Write | R8 | 0x010E0460 |
| SCANPLC_F16 | Read/Write | R8 | 0x010F0460 |
| SCANPLC_F17 | Read/Write | R8 | 0x01100460 |
| SCANPLC_F18 | Read/Write | R8 | 0x01110460 |
| SCANPLC_F19 | Read/Write | R8 | 0x01120460 |
| SCANPLC_F20 | Read/Write | R8 | 0x01130460 |
| SCANPLC_F21 | Read/Write | R8 | 0x01140460 |
| SCANPLC_F22 | Read/Write | R8 | 0x01150460 |
| SCANPLC_F23 | Read/Write | R8 | 0x01160460 |
| SCANPLC_F24 | Read/Write | R8 | 0x01170460 |
| SCANPLC_F25 | Read/Write | R8 | 0x01180460 |
| SCANPLC_F26 | Read/Write | R8 | 0x01190460 |
| SCANPLC_F27 | Read/Write | R8 | 0x011A0460 |
| SCANPLC_F28 | Read/Write | R8 | 0x011B0460 |
| SCANPLC_F29 | Read/Write | R8 | 0x011C0460 |
| SCANPLC_F30 | Read/Write | R8 | 0x011D0460 |
| SCANPLC_F31 | Read/Write | R8 | 0x011E0460 |
| SCANPLC_F32 | Read/Write | R8 | 0x011F0460 |
| SCANPLC_L1 | Read/Write | I4 | 0x04000460 |
| SCANPLC_L2 | Read/Write | I4 | 0x04010460 |
| SCANPLC_L3 | Read/Write | I4 | 0x04020460 |
| SCANPLC_L4 | Read/Write | I4 | 0x04030460 |
| SCANPLC_L5 | Read/Write | I4 | 0x04040460 |
| SCANPLC_L6 | Read/Write | I4 | 0x04050460 |
| SCANPLC_L7 | Read/Write | I4 | 0x04060460 |
| SCANPLC_L8 | Read/Write | I4 | 0x04070460 |
| SCANPLC_L9 | Read/Write | I4 | 0x04080460 |
| SCANPLC_L10 | Read/Write | I4 | 0x04090460 |
| SCANPLC_L11 | Read/Write | I4 | 0x040A0460 |
| SCANPLC_L12 | Read/Write | I4 | 0x040B0460 |
| SCANPLC_L13 | Read/Write | I4 | 0x040C0460 |
| SCANPLC_L14 | Read/Write | I4 | 0x040D0460 |
| SCANPLC_L15 | Read/Write | I4 | 0x040E0460 |
| SCANPLC_L16 | Read/Write | I4 | 0x040F0460 |
Event/User Change Log Items (All Models)
| Item | Access | Data Type | Description |
|---|---|---|---|
| UCLogEaliestDate | Read Only | DATE | Timestamp of earliest record |
| UCLogLatestDate | Read Only | DATE | Timestamp of latest record |
| UCLoTotRecs | Read Only | UI2 | Total number of records |
| UCLogUnReadRecs | Read Only | UI2 | Total number of unread records based on the location of the GETN continuation pointer stored in the driver for each device |
Extended Items
| Item | Data Type | Description |
|---|---|---|
| AdHocMeterConfig/1 | BSTR | Write to this tag to initialize an AdHoc Meter Config request |
| Demand GC Upload | UI1 | Writing a 1 to this triggers a GETS command to read the GC Structure |
| LastAlarmRecord | DATE | Last record date/time |
| LastChangeLogRecord | DATE | Last record date/time |
| LastDailyRecord | DATE | Last record date/time |
| LastDemandGCRecord | DATE | Last record date/time |
| LastDLogRecord | DATE | Last record date/time |
| LastEventRecord | DATE | Last record date/time |
| LastHourlyRecord | DATE | Last record date/time |
| LastTimeSync | DATE | Last time sync date/time |
| LastTimeSyncResult | I4 | The result of the last time sync attempt. |
| MoveDaily | UI4 | Move Daily Archive Pointer requested for run. Provide the new position as a Julian date/time. |
| MoveHourly | UI4 | Move Hourly Archive Pointer requested for run. Provide the new position as a Julian date/time. |
| TimeSync | I2 | Perform time synchronization. |
For assistance, please submit a ticket via our Support Portal, email autosol.support@autosoln.com or call 281.286.6017 to speak to a support team member.