Page Comparison

HART.CHANNEL_VERSION:n

STRING

10 character version number for the firmware in this channel. Read only.

85.0:n

HART.CHANNEL_IO:n

UI1

Indicates if channel is input (0) or output (1). Read only.

85.1:n

HART.COMM_MODE:n

UI1

0=Disabled, 1=Point to Point, 2=Multidrop.

85.2:n

HART.NUMBER_DEVICES:n

UI1

Number of devices connected in multidrop mode.

85.3:n

HART.COMM_STATUS:n

UI1

Communication status.  0=Not scanning, 1=Scanning normal, 2=Dual Master detected, 3=Pass thru, 4=Device in burst mode. Read only.

85.4:n

HART.ANALOG_MODE:n

UI1

Analog mode.  0=Disabled, 1=Enabled.

85.5:n

HART.PASS_THRU:n

UI1

Enables ROC protocol pass thru communication.  0=Disabled, 1=Enabled.

85.6:n

HART.PASS_THRU_TIMEOUT:n

UI4

Timeout (in millisecons) to resume after pass thru communications.

85.7:n

HART.HART_EU_VALUE:n

R4

EU value of analog input or output. Read only.

85.8:n

HART.HART_FAILSAFE_ON_RESET:n

UI1

0=Use last EU value on reset, 1=Use failsafe value on reset.

85.9:n

HART.HART_FAILSAFE_VALUE:n

R4

The value outputted when the unit is started.

85.10:n

HART.HART_MANUAL_VALUE:n

R4

The value used in output when scanning is in manual mode.

85.11:n

HART.HART_AUTO_VALUE:n

R4

The value used in output when scanning is in auto mode.

85.12:n

HART.HART_PHYSICAL_VALUE:n

R4

The current value of the output in engineering units.

85.13:n

HART.PHYSICAL_RAW_DA:n

UI2

Calculated digital-to-analog value.

85.14:n

HART.CALIBRATION_LIVE:n

R4

The live value when calibrating an AI

85.15:n

HART.CALIBRATION_ZERO:n

R4

The zero EU calibration value

85.16:n

HART.CALIBRATION_SPAN:n

R4

The span EU calibration value

85.17:n

HART.EU_RAW_VALUE:n

UI2

The EU value of AI or AO.

85.18:n

HART.EU_RAW_CALIBRATION_ZERO:n

UI2

The zero raw calibration value.

85.19:n

HART.EU_RAW_CALIBRATION_SPAN:n

UI2

The span raw calibration value.

85.20:n

HART.DEVICE_1_POLL_MODE:n

UI1

The polling mode for the device.  0=skip, 1=primary only, 2=all dynamic, 3=all slot, 4=full update.

85.21:n

HART.DEVICE_1_POLL_ADDRESS:n

UI1

Polling address for the device. Read only.

85.22:n

HART.DEVICE_1_STATUS:n

UI1

0=no device found, 1=communication, 2=comm error.

85.23:n

HART.DEVICE_1_ACTUAL_SCAN_PERIOD:n

R4

Period at which device is being updates.

85.24:n

HART. DEVICE_1_TAG:n

STRING

10 character tag that resides in this device. Read only.

85.25:n

HART.DEVICE_1_RESPONSE_CODE:n

UI2

Response code and status received from device. Read only.

85.26:n

HART.DEVICE_1_ACTIVE_ALARMS:n

UI1

Active alarms reported by device. Read only.

85.27:n

HART.DEVICE_1_CURRENT:n

R4

Current in milliamps. Read only.

85.28:n

HART.DEVICE_1_PERCENT_RANGE:n

R4

Percent of range reported by device. Read only.

85.29:n

HART.DEVICE_1_FAILSAFE_ENABLE:n

UI1

Enables the use of fail safe values for the dynamic variables when the unit resets. 

85.30:n

HART.DEVICE_1_PV_UNITS:n

UI1

Units code for primary variable reported by device. Read only.

85.31:n

HART.DEVICE_1_PV:n

R4

Value of primary variable reported by device. Read only.

85.32:n

HART.DEVICE_1_PV_FAILSAFE:n

R4

Primary fail safe value for device.

85.33:n

HART.DEVICE_1_SV_UNITS:n

UI1

Units code for secondary variable reported by device. Read only.

85.34:n

HART.DEVICE_1_SV:n

R4

Value of secondary variable reported by device. Read only.

85.35:n

HART.DEVICE_1_SV_FAILSAFE:n

R4

Secondary fail safe value for device.

85.36:n

HART.DEVICE_1_TV_UNITS:n

UI1

Units code for tertiary variable reported by device. Read only.

85.37:n

HART.DEVICE_1_TV:n

R4

Value of tertiary variable reported by device. Read only.

85.38:n

HART.DEVICE_1_TV_FAILSAFE:n

R4

Tertiary fail safe value for device.

85.39:n

HART.DEVICE_1_FV_UNITS:n

UI1

Units code for fourth variable reported by device. Read only. 

85.40:n

HART.DEVICE_1_FV:n

R4

Value of fourth variable reported by device. Read only.

85.41:n

HART.DEVICE_1_FV_FAILSAFE:n

R4

Fourth fail safe value for device.

85.42:n

HART.DEVICE_1_SLOT_0_ASSIGN:n

UI1

Slot 0 variable to request from device.

85.43:n

HART.DEVICE_1_SLOT_0_UNITS:n

UI1

Units of slot 0 variable to request from device. Read only.

85.44:n

HART.DEVICE_1_SLOT_0_VARIABLE:n

R4

Value of slot 0 variable requested from device.

85.45:n

HART.DEVICE_1_SLOT_1_ASSIGN:n

UI1

Slot 1 variable to request from device.

85.46:n

HART.DEVICE_1_SLOT_1_UNITS:n

UI1

Units of slot 1 variable to request from device. Read only.

85.47:n

HART.DEVICE_1_SLOT_1_VARIABLE:n

R4

Value of slot 1 variable requested from device.

85.48:n

HART.DEVICE_1_SLOT_2_ASSIGN:n

UI1

Slot 2 variable to request from device.

85.49:n

HART.DEVICE_1_SLOT_2_UNITS:n

UI1

Units of slot 2 variable to request from device. Read only.

85.50:n

HART.DEVICE_1_SLOT_2_VARIABLE:n

R4

Value of slot 2 variable requested from device.

85.51:n

HART.DEVICE_1_SLOT_3_ASSIGN:n

UI1

Slot 3 variable to request from device.

85.52:n

HART.DEVICE_1_SLOT_3_UNITS:n

UI1

Units of slot 3 variable to request from device. Read only.

85.53:n

HART.DEVICE_1_SLOT_3_VARIABLE:n

R4

Value of slot 3 variable requested from device.

85.54:n

HART.DEVICE_1_MESSAGE:n

STRING

40 character device message. 

85.55:n

HART.DEVICE_1_DESCRIPTION:n

STRING

20 character device description. 

85.56:n

HART.DEVICE_1_MANU_ID:n

UI2

Device manufacture ID. Read only.

85.57:n

HART.DEVICE_1_SERIAL:n

UI4

Device serial number. Read only.

85.58:n

HART.DEVICE_1_ID_NUMBER:n

UI4

Device sensor units. Read only.

85.59:n

HART.DEVICE_1_SENSOR_UNITS:n

UI1

Device sensor units. Read only.

85.60:n

HART.DEVICE_1_SENSOR_UPPER_LIM:n

R4

Device sensor upper limit. Read only.

85.61:n

HART.DEVICE_1_SENSOR_LOWER_LIM:n

R4

Device sensor lower limit. Read only.

85.62:n

HART.DEVICE_1_MINIMUM_SPAN:n

R4

Device minimum sensor span. Read only.

85.63:n

HART.DEVICE_1_OUTPUT_UNITS:n

UI1

Device output units. Read only.

85.64:n

HART.DEVICE_1_OUTPUT_UPPER_LIM:n

R4

Device output upper limit. Read only.

85.65:n

HART.DEVICE_1_OUTPUT_LOWER_LIM:n

R4

Device output lower limit. Read only.

85.66:n

HART.DEVICE_1_DAMPING_VALUE:n

R4

Device damping value. Read only.

85.67:n

HART.DEVICE_2_POLL_MODE:n

UI1

The polling mode for the device.  0=skip, 1=primary only, 2=all dynamic, 3=all slot, 4=full update.

85.68:n

HART.DEVICE_2_POLL_ADDRESS:n

UI1

Polling address for the device. Read only.

85.69:n

HART.DEVICE_2_STATUS:n

UI1

0=no device found, 1=communication, 2=comm error.

85.70:n

HART.DEVICE_2_ACTUAL_SCAN_PERIOD:n

R4

Period at which device is being updates.

85.71:n

HART. DEVICE_2_TAG:n

STRING

10 character tag that resides in this device. Read only. 

85.72:n

HART.DEVICE_2_RESPONSE_CODE:n

UI2

Response code and status received from device. Read only.

85.73:n

HART.DEVICE_2_ACTIVE_ALARMS:n

UI1

Active alarms reported by device. Read only.

85.74:n

HART.DEVICE_2_CURRENT:n

R4

Current in milliamps. Read only.

85.75:n

HART.DEVICE_2_PERCENT_RANGE:n

R4

Percent of range reported by device. Read only.

85.76:n

HART.DEVICE_2_FAILSAFE_ENABLE:n

UI1

Enables the use of fail safe values for the dynamic variables when the unit resets.

85.77:n

HART.DEVICE_2_PV_UNITS:n

UI1

Units code for primary variable reported by device. Read only.

85.78:n

HART.DEVICE_2_PV:n

R4

Value of primary variable reported by device. Read only.

85.79:n

HART.DEVICE_2_PV_FAILSAFE:n

R4

Primary fail safe value for device.

85.80:n

HART.DEVICE_2_SV_UNITS:n

UI1

Units code for secondary variable reported by device. Read only.

85.81:n

HART.DEVICE_2_SV:n

R4

Value of secondary variable reported by device. Read only.

85.82:n

HART.DEVICE_2_SV_FAILSAFE:n

R4

Secondary fail safe value for device.

85.83:n

HART.DEVICE_2_TV_UNITS:n

UI1

Units code for tertiary variable reported by device. Read only.

85.84:n

HART.DEVICE_2_TV:n

R4

Value of tertiary variable reported by device. Read only.

85.85:n

HART.DEVICE_2_TV_FAILSAFE:n

R4

Tertiary fail safe value for device.

85.86:n

HART.DEVICE_2_FV_UNITS:n

UI1

Units code for fourth variable reported by device. Read only.

85.87:n

HART.DEVICE_2_FV:n

R4

Value of fourth variable reported by device. Read only.

85.88:n

HART.DEVICE_2_FV_FAILSAFE:n

R4

Fourth fail safe value for device.

85.89:n

HART.DEVICE_2_SLOT_0_ASSIGN:n

UI1

Slot 0 variable to request from device.

85.90:n

HART.DEVICE_2_SLOT_0_UNITS:n

UI1

Units of slot 0 variable to request from device. Read only.

85.91:n

HART.DEVICE_2_SLOT_0_VARIABLE:n

R4

Value of slot 0 variable requested from device.

85.92:n

HART.DEVICE_2_SLOT_1_ASSIGN:n

UI1

Slot 1 variable to request from device.

85.93:n

HART.DEVICE_2_SLOT_1_UNITS:n

UI1

Units of slot 1 variable to request from device. Read only.

85.94:n

HART.DEVICE_2_SLOT_1_VARIABLE:n

R4

Value of slot 1 variable requested from device.

85.95:n

HART.DEVICE_2_SLOT_2_ASSIGN:n

UI1

Slot 2 variable to request from device.

85.96:n

HART.DEVICE_2_SLOT_2_UNITS:n

UI1

Units of slot 2 variable to request from device. Read only.

85.97:n

HART.DEVICE_2_SLOT_2_VARIABLE:n

R4

Value of slot 2 variable requested from device.

85.98:n

HART.DEVICE_2_SLOT_3_ASSIGN:n

UI1

Slot 3 variable to request from device.

85.99:n

HART.DEVICE_2_SLOT_3_UNITS:n

UI1

Units of slot 3 variable to request from device. Read only.

85.100:n

HART.DEVICE_2_SLOT_3_VARIABLE:n

R4

Value of slot 3 variable requested from device.

85.101:n

HART.DEVICE_2_MESSAGE:n

STRING

40 character device message. 

85.102:n

HART.DEVICE_2_DESCRIPTION:n

STRING

20 character device description. 

85.103:n

HART.DEVICE_2_MANU_ID:n

UI2

Device manufacture ID. Read only.

85.104:n

HART.DEVICE_2_SERIAL:n

UI4

Device serial number. Read only.

85.105:n

HART.DEVICE_2_ID_NUMBER:n

UI4

Device sensor units. Read only.

85.105:n

HART.DEVICE_2_SENSOR_UNITS:n

UI1

Device sensor units. Read only.

85.107:n

HART.DEVICE_2_SENSOR_UPPER_LIM:n

R4

Device sensor upper limit. Read only.

85.108:n

HART.DEVICE_2_SENSOR_LOWER_LIM:n

R4

Device sensor lower limit. Read only.

85.109:n

HART.DEVICE_2_MINIMUM_SPAN:n

R4

Device minimum sensor span. Read only.

85.110:n

HART.DEVICE_2_OUTPUT_UNITS:n

UI1

Device output units. Read only.

85.111:n

HART.DEVICE_2_OUTPUT_UPPER_LIM:n

R4

Device output upper limit. Read only.

85.112:n

HART.DEVICE_2_OUTPUT_LOWER_LIM:n

R4

Device output lower limit. Read only.

85.113:n

HART.DEVICE_2_DAMPING_VALUE:n

R4

Device damping value. Read only.

85.114:n

HART.DEVICE_3_POLL_MODE:n

UI1

The polling mode for the device.  0=skip, 1=primary only, 2=all dynamic, 3=all slot, 4=full update.

85.115:n

HART.DEVICE_3_POLL_ADDRESS:n

UI1

Polling address for the device. Read only.

85.116:n

HART.DEVICE_3_STATUS:n

UI1

0=no device found, 1=communication, 2=comm error.

85.117:n

HART.DEVICE_3_ACTUAL_SCAN_PERIOD:n

R4

Period at which device is being updates.

85.118:n

HART. DEVICE_3_TAG:n

STRING

10 character tag that resides in this device. Read only.

85.119:n

HART.DEVICE_3_RESPONSE_CODE:n

UI2

Response code and status received from device. Read only.

85.120:n

HART.DEVICE_3_ACTIVE_ALARMS:n

UI1

Active alarms reported by device. Read only.

85.121:n

HART.DEVICE_3_CURRENT:n

R4

Current in milliamps. Read only.

85.122:n

HART.DEVICE_3_PERCENT_RANGE:n

R4

Percent of range reported by device. Read only.

85.123:n

HART.DEVICE_3_FAILSAFE_ENABLE:n

UI1

Enables the use of fail safe values for the dynamic variables when the unit resets.

85.124:n

HART.DEVICE_3_PV_UNITS:n

UI1

Units code for primary variable reported by device. Read only.

85.125:n

HART.DEVICE_3_PV:n

R4

Value of primary variable reported by device. Read only.

85.126:n

HART.DEVICE_3_PV_FAILSAFE:n

R4

Primary fail safe value for device.

85.127:n

HART.DEVICE_3_SV_UNITS:n

UI1

Units code for secondary variable reported by device. Read only.

85.128:n

HART.DEVICE_3_SV:n

R4

Value of secondary variable reported by device. Read only.

85.129:n

HART.DEVICE_3_SV_FAILSAFE:n

R4

Secondary fail safe value for device.

85.130:n

HART.DEVICE_3_TV_UNITS:n

UI1

Units code for tertiary variable reported by device. Read only.

85.131:n

HART.DEVICE_3_TV:n

R4

Value of tertiary variable reported by device. Read only.

85.132:n

HART.DEVICE_3_TV_FAILSAFE:n

R4

Tertiary fail safe value for device.

85.133:n

HART.DEVICE_3_FV_UNITS:n

UI1

Units code for fourth variable reported by device. Read only.

85.134:n

HART.DEVICE_3_FV:n

R4

Value of fourth variable reported by device. Read only.

85.135:n

HART.DEVICE_3_FV_FAILSAFE:n

R4

Fourth fail safe value for device.

85.136:n

HART.DEVICE_3_SLOT_0_ASSIGN:n

UI1

Slot 0 variable to request from device.

85.137:n

HART.DEVICE_3_SLOT_0_UNITS:n

UI1

Units of slot 0 variable to request from device. Read only.

85.138:n

HART.DEVICE_3_SLOT_0_VARIABLE:n

R4

Value of slot 0 variable requested from device.

85.139:n

HART.DEVICE_3_SLOT_1_ASSIGN:n

UI1

Slot 1 variable to request from device.

85.140:n

HART.DEVICE_3_SLOT_1_UNITS:n

UI1

Units of slot 1 variable to request from device. Read only.

85.141:n

HART.DEVICE_3_SLOT_1_VARIABLE:n

R4

Value of slot 1 variable requested from device.

85.142:n

HART.DEVICE_3_SLOT_2_ASSIGN:n

UI1

Slot 2 variable to request from device.

85.143:n

HART.DEVICE_3_SLOT_2_UNITS:n

UI1

Units of slot 2 variable to request from device. Read only. 

85.144:n

HART.DEVICE_3_SLOT_2_VARIABLE:n

R4

Value of slot 2 variable requested from device.

85.145:n

HART.DEVICE_3_SLOT_3_ASSIGN:n

UI1

Slot 3 variable to request from device.

85.146:n

HART.DEVICE_3_SLOT_3_UNITS:n

UI1

Units of slot 3 variable to request from device. Read only.

85.147:n

HART.DEVICE_3_SLOT_3_VARIABLE:n

R4

Value of slot 3 variable requested from device.

85.148:n

HART.DEVICE_3_MESSAGE:n

STRING

40 character device message. 

85.149:n

HART.DEVICE_3_DESCRIPTION:n

STRING

20 character device description. 

85.150:n

HART.DEVICE_3_MANU_ID:n

UI2

Device manufacture ID. Read only.

85.151:n

HART.DEVICE_3_SERIAL:n

UI4

Device serial number. Read only.

85.152:n

HART.DEVICE_3_ID_NUMBER:n

UI4

Device sensor units. Read only.

85.153:n

HART.DEVICE_3_SENSOR_UNITS:n

UI1

Device sensor units. Read only.

85.154:n

HART.DEVICE_3_SENSOR_UPPER_LIM:n

R4

Device sensor upper limit. Read only.

85.155:n

HART.DEVICE_3_SENSOR_LOWER_LIM:n

R4

Device sensor lower limit. Read only.

85.156:n

HART.DEVICE_3_MINIMUM_SPAN:n

R4

Device minimum sensor span. Read only.

85.157:n

HART.DEVICE_3_OUTPUT_UNITS:n

UI1

Device output units. Read only.

85.158:n

HART.DEVICE_3_OUTPUT_UPPER_LIM:n

R4

Device output upper limit. Read only.

85.159:n

HART.DEVICE_3_OUTPUT_LOWER_LIM:n

R4

Device output lower limit. Read only.

85.160:n

HART.DEVICE_3_DAMPING_VALUE:n

R4

Device damping value. Read only.

85.161:n

HART.DEVICE_4_POLL_MODE:n

UI1

The polling mode for the device.  0=skip, 1=primary only, 2=all dynamic, 3=all slot, 4=full update.

85.162:n

HART.DEVICE_4_POLL_ADDRESS:n

UI1

Polling address for the device. Read only.

85.163:n

HART.DEVICE_4_STATUS:n

UI1

0=no device found, 1=communication, 2=comm error.

85.164:n

HART.DEVICE_4_ACTUAL_SCAN_PERIOD:n

R4

Period at which device is being updates.

85.165:n

HART. DEVICE_4_TAG:n

STRING

10 character tag that resides in this device. Read only.

85.166:n

HART.DEVICE_4_RESPONSE_CODE:n

UI2

Response code and status received from device. Read only.

85.167:n

HART.DEVICE_4_ACTIVE_ALARMS:n

UI1

Active alarms reported by device. Read only.

85.168:n

HART.DEVICE_4_CURRENT:n

R4

Current in milliamps. Read only.

85.169:n

HART.DEVICE_4_PERCENT_RANGE:n

R4

Percent of range reported by device. Read only.

85.170:n

HART.DEVICE_4_FAILSAFE_ENABLE:n

UI1

Enables the use of fail safe values for the dynamic variables when the unit resets.

85.171:n

HART.DEVICE_4_PV_UNITS:n

UI1

Units code for primary variable reported by device. Read only.

85.172:n

HART.DEVICE_4_PV:n

R4

Value of primary variable reported by device. Read only.

85.173:n

HART.DEVICE_4_PV_FAILSAFE:n

R4

Primary fail safe value for device.

85.174:n

HART.DEVICE_4_SV_UNITS:n

UI1

Units code for secondary variable reported by device. Read only.

85.175:n

HART.DEVICE_4_SV:n

R4

Value of secondary variable reported by device. Read only.

85.176:n

HART.DEVICE_4_SV_FAILSAFE:n

R4

Secondary fail safe value for device.

85.177:n

HART.DEVICE_4_TV_UNITS:n

UI1

Units code for tertiary variable reported by device. Read only.

85.178:n

HART.DEVICE_4_TV:n

R4

Value of tertiary variable reported by device. Read only.

85.179:n

HART.DEVICE_4_TV_FAILSAFE:n

R4

Tertiary fail safe value for device.

85.180:n

HART.DEVICE_4_FV_UNITS:n

UI1

Units code for fourth variable reported by device. Read only.

85.181:n

HART.DEVICE_4_FV:n

R4

Value of fourth variable reported by device. Read only.

85.182:n

HART.DEVICE_4_FV_FAILSAFE:n

R4

Fourth fail safe value for device.

85.183:n

HART.DEVICE_4_SLOT_0_ASSIGN:n

UI1

Slot 0 variable to request from device.

85.184:n

HART.DEVICE_4_SLOT_0_UNITS:n

UI1

Units of slot 0 variable to request from device. Read only. 

85.185:n

HART.DEVICE_4_SLOT_0_VARIABLE:n

R4

Value of slot 0 variable requested from device.

85.186:n

HART.DEVICE_4_SLOT_1_ASSIGN:n

UI1

Slot 1 variable to request from device.

85.187:n

HART.DEVICE_4_SLOT_1_UNITS:n

UI1

Units of slot 1 variable to request from device.

Read only.

85.188:n

HART.DEVICE_4_SLOT_1_VARIABLE:n

R4

Value of slot 1 variable requested from device.

85.189:n

HART.DEVICE_4_SLOT_2_ASSIGN:n

UI1

Slot 2 variable to request from device.

85.190:n

HART.DEVICE_4_SLOT_2_UNITS:n

UI1

Units of slot 2 variable to request from device.

Read only.

85.191:n

HART.DEVICE_4_SLOT_2_VARIABLE:n

R4

Value of slot 2 variable requested from device.

85.192:n

HART.DEVICE_4_SLOT_3_ASSIGN:n

UI1

Slot 3 variable to request from device.

85.193:n

HART.DEVICE_4_SLOT_3_UNITS:n

UI1

Units of slot 3 variable to request from device.

Read only.

85.194:n

HART.DEVICE_4_SLOT_3_VARIABLE:n

R4

Value of slot 3 variable requested from device.

85.195:n

HART.DEVICE_4_MESSAGE:n

STRING

40 character device message. 

85.196:n

HART.DEVICE_4_DESCRIPTION:n

STRING

20 character device description. 

85.197:n

HART.DEVICE_4_MANU_ID:n

UI2

Device manufacture ID. Read only.

85.198:n

HART.DEVICE_4_SERIAL:n

UI4

Device serial number. Read only.

85.199:n

HART.DEVICE_4_ID_NUMBER:n

UI4

Device sensor units. Read only.

85.200:n

HART.DEVICE_4_SENSOR_UNITS:n

UI1

Device sensor units. Read only.

85.201:n

HART.DEVICE_4_SENSOR_UPPER_LIM:n

R4

Device sensor upper limit. Read only.

85.202:n

HART.DEVICE_4_SENSOR_LOWER_LIM:n

R4

Device sensor lower limit. Read only.

85.203:n

HART.DEVICE_4_MINIMUM_SPAN:n

R4

Device minimum sensor span. Read only.

85.204:n

HART.DEVICE_4_OUTPUT_UNITS:n

UI1

Device output units. Read only.

85.205:n

HART.DEVICE_4_OUTPUT_UPPER_LIM:n

R4

Device output upper limit. Read only. 

85.206:n

HART.DEVICE_4_OUTPUT_LOWER_LIM:n

R4

Device output lower limit. Read only.

85.207:n

HART.DEVICE_4_DAMPING_VALUE:n

R4

Device damping value. Read only.

85.208:n

HART.DEVICE_5_POLL_MODE:n

UI1

The polling mode for the device.  0=skip, 1=primary only, 2=all dynamic, 3=all slot, 4=full update.

85.209:n

HART.DEVICE_5_POLL_ADDRESS:n

UI1

Polling address for the device. Read only.

85.210:n

HART.DEVICE_5_STATUS:n

UI1

0=no device found, 1=communication, 2=comm error.

85.211:n

HART.DEVICE_5_ACTUAL_SCAN_PERIOD:n

R4

Period at which device is being updates.

85.212:n

HART. DEVICE_5_TAG:n

STRING

10 character tag that resides in this device. Read only.

85.213:n

HART.DEVICE_5_RESPONSE_CODE:n

UI2

Response code and status received from device. Read only.

85.214:n

HART.DEVICE_5_ACTIVE_ALARMS:n

UI1

Active alarms reported by device. Read only.

85.215:n

HART.DEVICE_5_CURRENT:n

R4

Current in milliamps. Read only.

85.216:n

HART.DEVICE_5_PERCENT_RANGE:n

R4

Percent of range reported by device. Read only.

85.217:n

HART.DEVICE_5_FAILSAFE_ENABLE:n

UI1

Enables the use of fail safe values for the dynamic variables when the unit resets.

85.218:n

HART.DEVICE_5_PV_UNITS:n

UI1

Units code for primary variable reported by device. Read only.

85.219:n

HART.DEVICE_5_PV:n

R4

Value of primary variable reported by device. Read only.

85.220:n

HART.DEVICE_5_PV_FAILSAFE:n

R4

Primary fail safe value for device.

85.221:n

HART.DEVICE_5_SV_UNITS:n

UI1

Units code for secondary variable reported by device. Read only.

85.222:n

HART.DEVICE_5_SV:n

R4

Value of secondary variable reported by device. Read only.

85.223:n

HART.DEVICE_5_SV_FAILSAFE:n

R4

Secondary fail safe value for device.

85.224:n

HART.DEVICE_5_TV_UNITS:n

UI1

Units code for tertiary variable reported by device. Read only.

85.225:n

HART.DEVICE_5_TV:n

R4

Value of tertiary variable reported by device. Read only. 

85.226:n

HART.DEVICE_5_TV_FAILSAFE:n

R4

Tertiary fail safe value for device.

85.227:n

HART.DEVICE_5_FV_UNITS:n

UI1

Units code for fourth variable reported by device. Read only.

85.228:n

HART.DEVICE_5_FV:n

R4

Value of fourth variable reported by device. Read only.

85.229:n

HART.DEVICE_5_FV_FAILSAFE:n

R4

Fourth fail safe value for device.

85.230:n

HART.DEVICE_5_SLOT_0_ASSIGN:n

UI1

Slot 0 variable to request from device.

85.231:n

HART.DEVICE_5_SLOT_0_UNITS:n

UI1

Units of slot 0 variable to request from device. Read only.

85.232:n

HART.DEVICE_5_SLOT_0_VARIABLE:n

R4

Value of slot 0 variable requested from device.

85.233:n

HART.DEVICE_5_SLOT_1_ASSIGN:n

UI1

Slot 1 variable to request from device.

85.234:n

HART.DEVICE_5_SLOT_1_UNITS:n

UI1

Units of slot 1 variable to request from device. Read only.

85.235:n

HART.DEVICE_5_SLOT_1_VARIABLE:n

R4

Value of slot 1 variable requested from device.

85.236:n

HART.DEVICE_5_SLOT_2_ASSIGN:n

UI1

Slot 2 variable to request from device.

85.237:n

HART.DEVICE_5_SLOT_2_UNITS:n

UI1

Units of slot 2 variable to request from device. Read only.

85.238:n

HART.DEVICE_5_SLOT_2_VARIABLE:n

R4

Value of slot 2 variable requested from device.

85.239:n

HART.DEVICE_5_SLOT_3_ASSIGN:n

UI1

Slot 3 variable to request from device.

85.240:n

HART.DEVICE_5_SLOT_3_UNITS:n

UI1

Units of slot 3 variable to request from device. Read only.

85.241:n

HART.DEVICE_5_SLOT_3_VARIABLE:n

R4

Value of slot 3 variable requested from device.

85.242:n

HART.DEVICE_5_MESSAGE:n

STRING

40 character device message. 

85.243:n

HART.DEVICE_5_DESCRIPTION:n

STRING

20 character device description. 

85.244:n

HART.DEVICE_5_MANU_ID:n

UI2

Device manufacture ID. Read only.

85.245:n

HART.DEVICE_5_SERIAL:n

UI4

Device serial number. Read only.

85.246:n

HART.DEVICE_5_ID_NUMBER:n

UI4

Device sensor units. Read only.

85.247:n

HART.DEVICE_5_SENSOR_UNITS:n

UI1

Device sensor units. Read only.

85.248:n

HART.DEVICE_5_SENSOR_UPPER_LIM:n

R4

Device sensor upper limit. Read only.

85.249:n

HART.DEVICE_5_SENSOR_LOWER_LIM:n

R4

Device sensor lower limit. Read only.

85.250:n

HART.DEVICE_5_MINIMUM_SPAN:n

R4

Device minimum sensor span. Read only.

85.251:n

HART.DEVICE_5_OUTPUT_UNITS:n

UI1

Device output units. Read only.

85.252:n

HART.DEVICE_5_OUTPUT_UPPER_LIM:n

R4

Device output upper limit. Read only.

85.253:n

HART.DEVICE_5_OUTPUT_LOWER_LIM:n

R4

Device output lower limit. Read only.

85.254:n

HART.DEVICE_5_DAMPING_VALUE:n

R4

Device damping value. Read only.

85.255:n

SYSTEM.ROC_UNIT or SYSTEM.ROC_ADDRESS

UINT8

One-byte unit code of the station address. The unit code for a ROC address is configurable by the user. A 0 is used for broadcast.

91.0:n

SYSTEM.ROC_GROUP

UINT8

Group code of the station address.

91.1:n

SYSTEM.STATION_NAME

AC

A 20-character ASCII field for the station name.

91.2:n

SYSTEM.PART_VERSION

AC

Contains the software part number and version number string. READ ONLY.

91.3:n

SYSTEM.TIME_CREATED

AC

Contains the time and date stamp the firmware was created. READ ONLY.

91.4:n

SYSTEM.MANU_ID

AC

Contains manufacturing identification string. READ ONLY.

91.5:n

SYSTEM.PROD_DESCRIPTION

AC

Contains manufacturing description of product. READ ONLY.

91.6:n

SYSTEM.SERIAL_NUMBER

UINT32

Contains the serial number for the unit.  READ ONLY.

91.7:n

SYSTEM.MAX_EVENTS or SYSTEM.ROM_EVENTS

UINT16

Contains the maximum number of events that the Event Log may contain. READ ONLY.

91.8:n

SYSTEM.MAX_ALARMS or SYSTEM.ROM_ALARMS

UINT16

Contains the maximum number of alarms that the Alarm Log may contain. READ ONLY.

91.9:n

SYSTEM.MAX_PIDS or SYSTEM.ROM_PIDS 

UINT8

Contains the maximum number of PID loops that may run on the system. READ ONLY.

91.10:n

SYSTEM.MAX_AGAS or SYSTEM.ROM_AGAS

UINT8

Contains the maximum number of Meter Runs that may run on the system. READ ONLY. 

91.11:n

SYSTEM.MAX_FST or SYSTEM.ROM_FST

UINT8

Contains the maximum number of FSTs that may run on the system. READ ONLY.

91.12:n

SYSTEM.EVENT_INDEX

UINT16

Indicates the current event index in the Event Log. READ ONLY.

91.13:n

SYSTEM.ALARM_INDEX

UINT16

Indicates the current alarm index in the Alarm Log. READ ONLY.

91.14:n

SYSTEM.ACTIVE_PIDS

UINT8

Number of active PIDs

91.15:n

SYSTEM.ACTIVE_STATIONS

UINT8

Number of active stations.

91.16:n

SYSTEM.ACTIVE_ORIFICE

UINT8

Number of active orifice meter runs.

91.17:n

SYSTEM.ACTIVE_TURBINE

UINT8

Number of active turbine meter runs.

91.18:n

SYSTEM.FST_CLEAR

UINT8

Setting this parameter clears FST code from Flash ROM. 

•       0 – Does nothing. 

•       1 – Initiates clearing of FST code.

91.19:n

SYSTEM.CLEAR_CONFIG

UINT8

Used to clear the internal configuration memory stored in flash ROM.

•       0 = Do nothing

•       1 = Enable clearing of Configuration Memory

91.20:n

SYSTEM.WRITE_CONFIG

UINT8

Used to command the ROC to store certain point types (indicated throughout this document) to flash configuration memory

•       0 = Do nothing

•       1 = Perform Write to Configuration Memory

91.21:n

SYSTEM.WRITE_COMPLETE

UINT8

Used to indicate that the system is the process of writing the configuration to flash ROM

•       0 = Currently Performing the Write

•       1 = Completed the Write

READ ONLY.

91.22:n

SYSTEM.MPU_LOADING

FLP

Contains the current percentage of time the CPU is being loaded, updated every 5 seconds. READ ONLY.

91.23:n

SYSTEM.RESERVED

UINT8

Unused parameter. READ ONLY.

91.24:n

SYSTEM.IO_SCANNING

UINT8

Used to enable or disable scanning of all I/O in the system.

•       0 = Disabled

•       1 = Enabled

91.25:n

SYSTEM.WARM_START

UINT8

Used to re-start the system. A warm start is a reboot of the system without performing all the power-on-self tests.

•       0 = Do nothing

•       1 = Perform Warm Start

91.26:n

SYSTEM.COLD_START

UINT8

Used to re-start the system. A cold start always includes starting from the boot sector and performing power-on-self tests, plus the following options.

•       0 = Do nothing

•       1 = Restore Configuration from Flash

•       2 = Clear Alarms

•       3 = Clear Events

•       4 = Clear FSTs

•       5 = Clear History & Meter Runs

•       6 = Restore Configuration from Flash, Clear Alarms/Events/FST’s/History/Meter Runs

•       7 = Restore Configuration from Defaults

91.27:n

SYSTEM.LCD_INSTALLED

UINT8

•       0 = No LCD installed or LCD is disabled

•       1 = LCD installed and enabled READ ONLY.

91.28:n

SYSTEM.LCD_POWERSAVE

UINT8

Enables or disables the power saving feature of the LCD.

When enabled the display will stay on until the power off time expires. 0 – Disable Power Saving,  1 – Enable Power Saving.

Note: Since this functionality has not yet be added to the firmware (as of Version 1.00) this parameter is currently R/O. When the functionality is added, it will be made R/W.

91.29:n

SYSTEM.LCD_OWNER

UINT8

The current owner of the LCD. This is used if a user C program is needed to run the LCD.

•       0 = LCD

•       1 = User C Program 1

•       2 = User C Program 2

•       3 = User C Program 3

•       4 = User C Program 4

•       5 = User C Program 5

•       6 = User C Program 6

•       7 = User C Program 7

•       8 = User C Program 8

91.30:n

SYSTEM.BAUD_RATE_0

UINT32

The baud rate that baud rate generator #0 is to be set to.

91.31:n

SYSTEM.BAUD_RATE_1

UINT32

The baud rate that baud rate generator #1 is to be set to.

91.32:n

SYSTEM.BAUD_RATE_2

UINT32

The baud rate that baud rate generator #2 is to be set to.

91.33:n

SYSTEM.BAUD_RATE_3

UINT32

The baud rate that baud rate generator #3 is to be set to.

91.34:n

SYSTEM.CRC_CHECK

UINT8

The CRC check flag. If this flag is enabled, a CRC will be appended to all messages and a CRC will be expected on all received messages. Disabled = 0, Enabled = 1.

91.35:n

SYSTEM.LED_ENABLE

UINT8

Indicates the number of minutes the LEDs will be on before automatically turning themselves off. (The LED buttons will active the LEDs for the configured time).

•       0 = LEDs always on

•       1 - 60 = Number of minutes LEDs will be on

91.36:n

SYSTEM.BOOT_PART_NUM

AC

Contains the boot software part number and version number string. READ ONLY.

91.37:n

SYSTEM.BOOT_FIRMWARE_TIME

AC

Contains the time and date stamp the boot firmware was created. READ ONLY.

91.38:n

SYSTEM.ACTIVE_ODORIZERS

UINT8

Number of active odorizers

91.39:n

SYSTEM.CLEAR_HISTORY_CONFIG

Clears history database and resets configuration back to factory defaults without power cycling the ROC.

Don't clear = 0, Clear = 1.

91.40:n